Hi,

IMPORTANT: PLEASE ALWAYS BACKUP YOUR DATA FIRST BEFORE TOUCHING PARTITION TABLES ETC

first there are a few tools we need to accomplish this: resize2fs, lvscan, lvresize. Use "lvscan" to show your LVM group(s).

Here the steps to extend your LV:

1. # lvscan
   Scans for available LV
2. # fschk.ext3 /dev/VolGroup00/LogVol00
   Does a sanity check and corrections on the filesystem before further manipulation. Here the type is Ext3.
3. # lvresize -L 15G /dev/VolGroup00/LogVol00
   Sets capacity of the concerned LV (here LogVol00) to 15 GB
4. # resize2fs /dev/VolGroup00/LogVol00 15G
   Resizes the partition inside the LV to a capacity of 15 GB

Here are the steps to shrink your LV:

1. # lvscan
   Scans for available LV
2. # fschk.ext3 /dev/VolGroup00/LogVol00
   Does a sanity check and corrections on the filesystem before further manipulation. Here the type is Ext3.
3. # resize2fs /dev/VolGroup00/LogVol00 15G
   Sets capacity of the concerned LV (here LogVol00) to 15 GB
4. # lvresize -L 15G /dev/VolGroup00/LogVol00
   Sets capacity of the concerned LV (here LogVol00) to 15 GB

All these steps can be done with the disk online, except for the root partition. If you want to modify this, you have to boot into a live cd. Also note that step 3 and 4 are inverted. If you want to increase your capacity you first need to grow your LV then the partition, if you want to shrink your capacity first shrink your partition then the LV. PLEASE TAKE CARE that your LV is NOT smaller than your partition! In this case DATA LOSS is almost sure.

Hello,

with NIC Bonding or Port Trunking you can provide higher throughput and redundency to your network cards. Basically it bonds two, let's say 1Gb network cards, to one 2Gb card. Bonding can be achieved with more than 2 cards in a system.

There are several modes:

Mode 0 (round-robin – load balancing/fault tolerence):
This is the default mode and sends packets from the first to the last slave. 1st packet -> 1st NIC, 2nd packet -> 2nd NIC, 3rd packet -> 1st NIC etc…

Mode 1 (active backup – fault tolerence):
In this mode only 1 card/slave is active at the moment. Another takes over as soon as the other goes down. Only the MAC address of the bond is visible on the outside.

Mode 2 (balance-xor – load balancing/fault tolerence – Static Link Aggregation):
In this mode every destination gets the packets from the same source address based on MAC addresses.

Mode 3 (broadcast – fault tolerence):
In this mode all packets go out on every interface. Incoming traffic is not affected.

Mode 4 (802.3ad – Dynamic Link Aggregation, LACP):
In this mode there is a group created wth the same speed an duplex possibilities according to IEEE 802.3ad. There are some prerequisites fot this: Ethtool support in drivers to get speed and duplex of each slave and a switch which supports 802.3ad.

Mode 5 (balance-tlb – load balancing):
In this mode the outgoing packets are distributed over all slaves, but only the active slaves receives packets. If this goes down another slave takes over.

Mode 6 (balance-alb – load balancing):
In this mode all outgoing and incoming traffic in distributed over all salves.

Now after shortly explaining all modes here how to create such a bond:

• add these lines to /etc/modprobe.conf:
  alias bond0 bonding
• create and open the file /etc/sysconfig/network-scripts/ifcfg-bond0:
  DEVICE=bond0
  IPADDR=<ip address>
  NETMASK=<your netmask>
  NETWORK=<network>
  BROADCAST=<broadcast>
  GATEWAY=<gateway>
  ONBOOT=yes
  BOOTPROTO=none
  USERCTL=no
  BONDING_OPTS="mode=<your selected mode (0-6)> miimon=100"
• then change your /etc/sysconfig/network-scripts/ifcfg-ethX files to:
  DEVICE=ethX
  ONBOOT=yes
  BOOTPROTO=none
  USERCTL=no
  MASTER=bond0
  SLAVE=yes

Now you should only need to restart your server. If you can't restart it please load the bond kernel module and restart your network:

# modprobe bonding
(ATTENTION: My host's connection froze here and i had to go to the physical server to restart the network)
# /etc/init.d/network restart

Hello,

first of all i explain how you can set your timezone through the terminal. This is quite easy:

check the available timezones on your machine with:
# ls /usr/share/zoneinfo

and copy them over to /etc/localtime (e.g. Europe/Luxembourg)
# cp /usr/share/zoneinfo/Europe/Luxembourg /etc/localtime

done.

Next step is the syncing with an ntp server. First check is ntp is installed on your system with
# which ntp

if it's not installed you get nothing in return. so install it with:
# yum install ntp

the config file which is used for the ntp is /etc/ntp.conf. There you can configure the time servers you want to use. For a list of servers visit www.ntp.org or go here. Here is an example for Luxembourg time servers, remove the old ones and insert the following lines instead:

server 2.lu.pool.ntp.org
server 3.europe.pool.ntp.org
server 0.europe.pool.ntp.org

Note:
Inside the ntp.conf you find 2 lines starting with "server … # local time" and "fudge". Comment out these lines as they can prevent proper syncing.

Now start the ntp daemon and set it up at boot time:
# /etc/init.d/ntp start
# chkconfig ntp on

Hope this helps someone out there!